Shower & Bathtub Installation in High Point, NC
New tubs, showers and valves installed with the plumbing done right behind the wall, from the drain to the pressure-balance valve.
- Tub and shower replacement
- Valve and drain work
- Pressure-balance valves
- Free estimates
Where The Plumber's Work Fits In A Bathroom Remodel
Shower and tub installation covers the plumbing a remodel depends on: the valve, the drain and trap, the supply lines to the tub spout and showerhead, and the connections to the wall or pan. Tile, waterproofing and finish carpentry may be done by a separate trade, so ask who owns each step before work starts.
A tub swap in the same location is simpler than moving the drain or building a new walk-in shower. Moving the drain means working in the floor or slab, which changes both cost and schedule.
Common Shower And Tub Options
The right choice depends on the room, the budget and who will use it.
| Option | What it involves | Good fit |
|---|---|---|
| Tub replacement, same size | Remove the old tub, set the new one on the existing drain | Straight swap in a standard alcove |
| Tub-to-shower conversion | Remove the tub and build a shower base or pan in the space | Easier entry, adult-focused homes |
| Prefab shower unit | A one-piece or paneled shower with a drain and valve | Quick, lower-cost remodel |
| Custom tile shower | A shower pan with waterproofing and tile | Full remodel with design choices |
| Valve and trim update | Replace the valve body and trim without changing the tub | Leaky or worn valve, fresh look |
Shower Leaking Or Valve Failing?
Call and describe the problem. Estimates for installation are free.
What The Plumbing Code Requires
The NC Plumbing Code follows the International Plumbing Code (IPC). Shower valves must be pressure-balance or thermostatic mixing types, which keep the water from turning scalding if someone flushes a toilet. A shower compartment generally needs a finished area of at least 900 square inches and a 30-inch minimum dimension.
Drains need an accessible trap and a correct vent. Set the water heater near 120 degrees Fahrenheit, which is widely recommended to reduce scald risk. Permits may apply to tub or shower installation, and the plumber should confirm with the local inspections office.
Bathtub Versus Walk-In Shower
Bathtub
- Soaking and bathing small children
- Often better for resale in family homes
- Needs more floor space and a higher step
- Tub replacement is relatively simple
Walk-in shower
- Easier entry and less cleaning
- Can use space more efficiently
- Needs proper waterproofing and pan work
- Better for aging in place
What To Do If A Shower Leaks Behind The Wall
A shower leak that stays hidden can rot framing and feed mold.
- 1
Stop using the shower and close the main valve if water is running inside the wall.
- 2
Check the ceiling and walls below and beside the shower for stains or swelling.
- 3
Look for loose tiles, cracked grout or a soft spot at the tub edge.
- 4
Keep people away from sagging ceilings, which may be holding water.
- 5
Photograph the damage and call a plumber to test the valve, pan and drain.
How A Shower Or Tub Installation Goes
- 1
Measure and plan
The plumber checks the rough-in, drain location and wall condition.
- 2
Quote
You receive a price for the plumbing scope before any demolition.
- 3
Demo and rough-in
The old fixture is removed and new valve, drain and supply lines are set.
- 4
Test and finish
Water is tested before walls close, then the trim and fixtures are completed.
What Plumbers Find Behind Older High Point Bathrooms
In houses from the Uptown Suburbs district and the mill village, bathrooms often sit over crawlspaces. Floors may be soft near the tub from years of seepage, and cast-iron drains may be corroded. A bathroom remodel is a good time to replace old galvanized supply stubs, which can restrict flow and make the new showerhead feel weak.
South-side ranches usually have drain lines under the slab, so relocating a tub means cutting concrete. If a leak has already damaged the wall or floor, professional water damage restoration addresses that, and electronic leak detection can locate the plumbing source. Pair a remodel with faucet and sink work and toilet installation to finish the room in one visit.
What Affects Shower And Tub Installation Cost
Free estimates for installation
The plumbing scope is priced after a look at the room, and you approve it before demolition. Call for your real number.
Shower And Bathtub Installation Questions
A straight swap in the same spot is often done in a day or two. Moving the drain, building a shower base or adding tile takes longer.
Yes, in many bathrooms. It involves removing the tub, building a shower base and drain, and waterproofing the walls.
A shower valve that keeps the water temperature steady when pressure changes elsewhere in the house, which helps prevent scalding.
It can depend on the scope, especially if the drain or supply lines move. The plumber should confirm requirements with the local inspections office.
Often old supply pipe behind the wall is restricted by corrosion or the pressure is low. A plumber can test flow at the valve.
Planning a bathroom? Call for an estimate.
Call (336) 453-0472Planning A Bathroom Update?
Call about shower and bathtub installation in High Point, Jamestown, Archdale, Trinity, Thomasville, Randleman and Greensboro.
Call (336) 453-0472